What did you do TO your Bronco Sport today?

[Red_405]

changed the Blue oval to Black!
Removed the OB sticky.
Added the sweet Black Bronco emblem.
& convinced my hubby to wire the side markers in!
Windows are getting tinted this wkend, she sure is coming together!

Sponsored

 

[Jrl]

changed the Blue oval to Black!
Removed the OB sticky.
Added the sweet Black Bronco emblem.
& convinced my hubby to wire the side markers in!
Windows are getting tinted this wkend, she sure is coming together!

changed the Blue oval to Black!
Removed the OB sticky.
Added the sweet Black Bronco emblem.
& convinced my hubby to wire the side markers in!
Windows are getting tinted this wkend, she sure is coming together!

Very nice , great taste. Looking good .

 

[Horse n Buggy]

I installed the AVS "Bugflector II" last night, guess I get to find out how well it holds up to some of these Ian winds.

 

[Wolf256]

Today, I went to Silverdale and while I didn’t do anything to my Sport, I did follow this F250 towing a Jeep up the highway. It just struck me as funny. For those that will say pics or it didn’t happen, here you go.

 

[Wolf256]

I installed the AVS "Bugflector II" last night, guess I get to find out how well it holds up to some of these Ian winds.

Is that the bolt on one and was it difficult?

 

[Wolf256]

changed the Blue oval to Black!
Removed the OB sticky.
Added the sweet Black Bronco emblem.
& convinced my hubby to wire the side markers in!
Windows are getting tinted this wkend, she sure is coming together!

I really like those marker lights. Is the white wired to the headlights/DRL’s? Could you ask hubby if they were difficult and how long it took?

 

[Red_405]

I really like those marker lights. Is the white wired to the headlights/DRL’s? Could you ask hubby if they were difficult and how long it took?

It took 30-45 mins. Yes, White is wired to DRL & Amber to turn signal.

There is a video of installation I found on the forum, it was helpful. Pic of wiring below from video.

(https://www.broncosportforum.com/forum/threads/tectico-or-dzg-light-installation.6962/)

 

[Horse n Buggy]

Is that the bolt on one and was it difficult?

It was not terribly difficult, my wife helped install it and it only took about 10 minutes.

You remove 6 of the plastic push pins that hold the hood seal in place. Then, at those locations, the Deflectors mounting tabs slide between the seal and the hood where it is secured with provided self taping screws into the holes that were you previously removed the plastic push pins from.

Most confusing part was which direction you spin the two rubber topped hood stops so it will close properly.

 

[Major Kong]

finally sprung for a full size spare
conundrum
mini spare

discarding to trash just doesn't sit well
curbside metal scavengers may be best bet
any suggestions

 

[Bluebaru]

I got my Flatout GR+ coilovers installed to day but didn't have time to set the final ride height or install the toe arm extension. Currently sitting at ~1.25" up.

 

[Jrl]

I got my Flatout GR+ coilovers installed to day but didn't have time to set the final ride height or install the toe arm extension. Currently sitting at ~1.25" up.

That is perfect, and it sets exactly as my first edition,it has a 1.5 left.

 

[Emma77]

Added a wireless carplay adapter

 

[Wolf256]

It was not terribly difficult, my wife helped install it and it only took about 10 minutes.

You remove 6 of the plastic push pins that hold the hood seal in place. Then, at those locations, the Deflectors mounting tabs slide between the seal and the hood where it is secured with provided self taping screws into the holes that were you previously removed the plastic push pins from.

Most confusing part was which direction you spin the two rubber topped hood stops so it will close properly.

Did this today, by myself. Still haven’t got the hood stops correct. I can tell anyone else going with this shield that the direction of 1 and 1/2 turns counter clockwise is not correct.

ETA: Turns out it was 4 or 5 full turns. The direction given in the instructions is counter clockwise. That just kept raising the hood. Clockwise was what lowered the hood stops. Also, for those, like me, that could have used a bit more instruction, you only have to remove the six tabs. If you have a second person it would be much easier to determine which of those tabs to remove. The shield isn’t heavy, just awkward.

 

[jimharrison1950]

Looks fantastic! Where did you get the roof basket and how does the spare mount on top?

Ordered our new 2023 Ford Bronco Sport Outer Banks Hot Red Pepper Fully Loaded at MSRP!

 

[JAD67428]

Engine Cover Installed!!!

Sponsored