What did you do TO your Bronco Sport today?

[Tigger]

I like the mud flaps. The OEM cap only cost me $6. I suggest ordering it and now 20% off

For others discussing cup holders, here are mine from Etsy.

 

[Escape2Bronco]

Went from 245/70

front

Rear
To 245/65 and then checked clearances

Looks like a lot of clearance in the last picture. Both above and below the tire!

 

[bjbena]

Bought/installed OEM crossbars and applied Chemical Guys Blacklight.

That Kodiak Brown definitely pops now.

 

[AGLzaca]

Had the front windshield tint strip done, which is the legal allowed tint here.

 

[Major Kong]

Yesterday
Spot this

https://www.broncosportforum.com/forum/threads/project-obronco.2688/post-102261

Pop the hood to make sure I don't already have one
Basemodelluckytohavehood.jpeg
Nope, just as I would have expected
Size it up
Looked pretty barren
Stark
Flat
Plastic
Remedy: Need this
Place order Fordparts.com late in evening
Delivery truck this AM
Done deal
Noise reduction
I believe so

Thanks for the part no's Glamdring70

Anyone have any intel on the (green arrows) four tubing ports?

 

[dakman]

Did first oil change and installed my new light bar. No lights yet but now I can decide which ones and they will hang down.

 

[Meanderthal]

Did first oil change and installed my new light bar. No lights yet but now I can decide which ones and they will hang down.

Which light bar is that?

 

[Wabarca2]

Which light bar is that?

It's rally innovations they have a skid plate too

 

[dakman]

It's rally innovations they have a skid plate too

Yes this is correct. I got the skid plate to but it hasn't arrived yet.

 

[Major Kong]

Rubber Rear Seat Backing
Base model BS
No seat mounted snaps
Preliminary set-up
Fasten using velcro
I'll let you know how it goes
Side note
Go to cash out
Hit the cashiers window
"I'd like to use Paypass points"
Oh, for that you need to go to the specialist window
"Howdy specialist. I'd like to use my Passpoints"
Oh, shows you have 42,000. You're good to go. Take your parts.
And AGAIN some how points are never deducted
Sure they'll find it someday
But until then
I'd have to say from the last couple visits I'm a pro at deficit spending
Think I'll run for Congress

 

[Jrl]

Rubber Rear Seat Backing
Base model BS
No seat mounted snaps
Preliminary set-up
Fasten using velcro
I'll let you know how it goes
Side note
Go to cash out
Hit the cashiers window
"I'd like to use Paypass points"
Oh, for that you need to go to the specialist window
"Howdy specialist. I'd like to use my Passpoints"
Oh, shows you have 42,000. You're good to go. Take your parts.
And AGAIN some how points are never deducted
Sure they'll find it someday
But until then
I'd have to say from the last couple visits I'm a pro at deficit spending
Think I'll run for Congress

You can buy the button fastners in a kit . They are a very useful item . Enjoy

 

[ck122]

scoop and visors

 

[Major Kong]

You can buy the button fastners in a kit . They are a very useful item . Enjoy

Not much luck finding snap fasteners
FordParts.com seems to suggest pop riveting???
Any link for a part number would be appreciated.
Rather take another approach than the pop-rivet
Say things get wet and you need to remove rubber mat
Rivet seems less favorable for removal purposes
After velco option No. 2 is push pin restraint

 

[PonyDriver43]

Yesterday
Spot this

https://www.broncosportforum.com/forum/threads/project-obronco.2688/post-102261

Pop the hood to make sure I don't already have one
Basemodelluckytohavehood.jpeg
Nope, just as I would have expected
Size it up
Looked pretty barren
Stark
Flat
Plastic
Remedy: Need this
Place order Fordparts.com late in evening
Delivery truck this AM
Done deal
Noise reduction
I believe so

Thanks for the part no's Glamdring70

Anyone have any intel on the (green arrows) four tubing ports?

My 12/23/21 built 2022 Outer Banks has this cushion device.
I thought it is an additional inflation device that inflated in the event the collision avoidance system failed. The green arrows point to the chip controlled ports that open when in SPORT GOAT mode so you can hear the Little Engine That Could better.
That's what I read on the infonet anyway.

 

[Glamdring70]

Thanks for the part no's Glamdring70

Anyone have any intel on the (green arrows) four tubing ports?

Heh heh. I didn't drop that one here lest it lead to a run on the parts like the Engine Cover crisis of 2022. Glad you got in before the stampede!

I am still trying to figure out the other 4 plastic pegs. My belief is that there is some piece of hardware (like a brake cylinder?) that attaches to the firewall via the same push retainer system, in larger gauges. I have looked online at other Ford engine bays like EcoSport and Escape and haven't found anything. Maybe on the electric Mavericks???

Sponsored