What did you do TO your Bronco Sport today?

[Bt_okst]

I have the flares from ford accessories, the front mudflaps have to be trimmed but i had ford put them on with absolutely no problems...i ordered my bronco with mudflaps, and had flares added....i got my spacers from amazon...but researched...and found the ones made by titan had alot of good reviews...just wanted the cheaper price from amazon.
I ordered me some new tires....
Size 245/70 17...Venom Power Terra Hunter X/T....havent put on yet, but using tirecalculator.com...i compared my oem to the new ones...using the wheel offset ...it showed that my new tires were only 4mm closer to inside...with the 1 inch spacers...so im assuming the tires will fit...but dont know yet...i will let yall know results when i get them fitted....the 245/70 17 are an inch and half taller..do we will see.

can you take pics to show what they trimmed on the mud flaps and tell me what they did? My dealer won't install them as they said even with trimming they wouldn't work. I knew that was BS. Want to see how to install them myself.

Thanks!!!

Sponsored

 

[chipearly]

Finally warm enough today that I was able to put on the deflector

 

[Jasonj7858]

can you take pics to show what they trimmed on the mud flaps and tell me what they did? My dealer won't install them as they said even with trimming they wouldn't work. I knew that was BS. Want to see how to install them myself.

Thanks!!!

Your dealer is lying to you...u dont have to trim the back at all and the front you just hold up to fender and trace curve of fender, trim and bolt on.

 

[Bt_okst]

Your dealer is lying to you...u dont have to trim the back at all and the front you just hold up to fender and trace curve of fender, trim and bolt on.

ty, this is what i needed.

 

[Deleted member 6350]

can you take pics to show what they trimmed on the mud flaps and tell me what they did? My dealer won't install them as they said even with trimming they wouldn't work. I knew that was BS. Want to see how to install them myself.

Thanks!!!

Will these fit ? I know it says 21-23 but I don’t think they changed anything for 2024 you can check with your local Ford Parts Counter for Sure. Mine is a 23 and I didn’t have to trim Anything.

https://accessories.ford.com/bronco-sport-2021-molded-black-front-splash-guard-pair-1

I just checked the website again and if you click on “fits these vehicles” it says 21-24

 

[Bt_okst]

Will these fit ? I know it says 21-23 but I don’t think they changed anything for 2024 you can check with your local Ford Parts Counter for Sure. Mine is a 23 and I didn’t have to trim Anything.

https://accessories.ford.com/bronco-sport-2021-molded-black-front-splash-guard-pair-1

I just checked the website again and if you click on “fits these vehicles” it says 21-24

I got the molded flaps. Does yours have the bushwacker flares? Everyone is saying they have to be trimmed to fit with those flares.

 

[Deleted member 6350]

I got the molded flaps. Does yours have the bushwacker flares? Everyone is saying they have to be trimmed to fit with those flares.

Ah sorry no flares

 

[Horse n Buggy]

Also added lockable mounts for my traction boards to the top of my box. Pics to follow of it back on top of my sport when the sun is out and it's not raining

No noticeable increase in wind noise. Clears my garage door. Bolts on and locks easily.

 

[Horse n Buggy]

Also added lockable mounts for my traction boards to the top of my box. Pics to follow of it back on top of my sport when the sun is out and it's not raining

The case art is essentially an Easter egg because no one is going to see it let alone make out what it is without flying a drone over the car or being on a bridge above me so I'll probably not have a good top down picture for a while, till then this is the best I could do

 

[acuity]

-RC nudge bar
-RC amber DRL cube lights
-Rhino rack cross bars
-Matte black Hyper-dip OEM OBX rims
-Matte black Plasti-dip rear and front “BRONCO/BRONCO SPORT”
-Falken tires

Upcoming:
-Aeroskin II
-Possibly more RC lights/light control panel

 

[CloneOBX]

-RC nudge bar
-RC amber DRL cube lights
-Rhino rack cross bars
-Matte black Hyper-dip OEM OBX rims
-Matte black Plasti-dip rear and front “BRONCO/BRONCO SPORT”
-Falken tires

Upcoming:
-Aeroskin II
-Possibly more RC lights/light control panel

Wheels Look great. Ill have to look into the hyper dip for mine. What are the brackets for on the upper part of the nudge bar? Looks like the lights are mounted on the lower portion. Thanks

 

[acuity]

The brackets I used were from Amazon: the 1.75-2.00IN size of (Audak 1 Pair Aluminum Mounting Bracket Kit Tube Clamp for 1.625 1.75 1.875 2 Inch Bullbar Roof Rack Roll Cage Horizontal Bar (1.6 to 2 Inch Adjustable).

However, I ended up taking them off as either due to the size of the specific brackets I purchased or the variations in the diameter of the bar I wasn’t able to get them tight enough to where they wouldn’t spin under minimal force. The brackets come with different size rubber pads. Maybe a different size bracket would work or you’ll have better luck but I’m unsure.

 

[westcoaster818]

I had 20% tint installed on the front windows.

Looks great. Get the ford windeflectors too it will be bad ass

 

[strckerie]

Today we installed the front license plate bracket with new decorative plate...very happy with the look!

 

[B-Dog15]

Added BFG KO2 (245/65r17) which makes the BS look so much better imo. Also added vinyl “R” overlays on front and back which I also think looks smooth. Going for a “Raptor” look and will be adding red accents in interior soon as well.
P.S don’t pay any mind to how dirty my car is please…