Search results

we all saw that fuse in the engine compartment. But researching throughout the forum, everyone has expressed that the engine fuse box and wiring is a nightmare. you’re better off getting a relay control box and a separate switch. Some switches have backlit displays where you would run a fuse...

no, I didn’t have to take the grill off.The entire bumper/grille is one piece that takes a lot of effort to get off. when I’m don’t with work, I’ll take photos of what I took off from under the hood to access the area that I installed the Raptor Lights. Super simple and easy access.

Here is a photo of the offset I had to do for the lights. The mounts on the nudge bar are set at a 45 degree angle after install. With the brackets installed for the lights, the lights would not fit correctly, they would point down to the street. So, I Jerry-rigged this offset and it works...

It was easy. I think I have links to the mesh and rubber trim in an earlier post. I might play around with different insert molding to create a better fit/look. But it beats the exposed plain look of the lights mounted on the plastic honeycomb. When I have a full day to devote to working on the...

Audexen 7” work lights - based on the mount bracket angle and their size, I had to offset it just a tad. I grabbed some 2” metal joiner plates, drilled out the holes larger to fit the mounting bolts. I just need to powder coat them (and probably all the mounting hardware) and it’s will look...

@GoatsyBanks All hooked up and working. I’m Loving the Raptor trim lights!

Got my RC Nudge Bar installed with Audexen 7” 3-way LEDs Raptor Trim Under Grille Accent Lights not in photo: RC 1.5” Level/Lift Side vent LED signal markers (replaces the plastic vent clip-ins in front of driver/passenger door)

The only Nilight item I have is the 6 gang switch panel. Very easy install. I had to create a mounting station for the control box under the hood. Because the switch panel is so thin, it can essentially be mounted anywhere in the cabin (bracket and adhesive options, both included in kit). I ran...

I’ve tried all the scenarios you went through above, it’s like I have a super FOB that bypasses all security. The car does lock, and I’ve made it a custom to die the double tap because I like hearing the horn for added reassurance. I’ve locked it and left my car in my house, gone back out and...

And just to clarify, when I mean “hard” lock - I mean that I can lock my car via the App, and the Intelligent Access sensor disarms.

Looks like I’m going to have to take it in to get serviced. No matter where I stand around the car, after locking, other doors still open. And I tried the steps per @Michigunman‘s post… didn’t work The only “hard” lock that I’ve been able to initiate is the one via the FordPass App. Other than...

Hey Forum Folks, So today I was pumping gas and a drive by snuck into my passenger side door and grabbed my computer bag off the seat as I was placing my card in the pump reader. I didn’t feel the car door open/close from the other side of the car, didn’t hear it either due to another car in...

Yep, that’s the one

No, I don’t unfortunately. That has seemed to be a big topic of discussion throughout the forum. I’ve seen some people say they were going to tap into some instrument panel wires, but I have yet to see a diagram/photos/recommendations. The only wiring info I found was for splicing in my side...

I hear ya. I picked up my BS second week in January. Since then I’ve just been in MOD overhaul, but can’t seem to find the time to just take a day and get it done. Ive only been able to get my lift,tires, and side door vent lights installed fully. Everything else I have done is just partially...

Here is the original post with some step by step install and info on what wires to splice. I followed it all step by step and all works like a charm https://www.broncosportforum.com/forum/threads/project-obronco.2688/post-84674

I got them installed on mine. Look great, work great, easy install. I did splice them directly into the signal light wiring from the headlights. Ive had no light dimming issues or electrical issues post install. The wires are a very thin gauge, and I recommend taking some hot glue to the back...

Sorry for the delayed response. I got the Bona Grille Lights. Cheap, sufficient. Wire hosing is complete crap, so I stripped it all and re-secured with better flex conduit tubing. I have not gotten them hooked up yet though, and im just going to run it into a switch on my controller. It came...

You can disable the door sensor if necessary. It’s most likely set up like the full size Bronco for its optional door removal. I remember the first time I took the doors off my Jeep and forgot about the sensor… drained my battery due to the overhead lights staying on the entire time I was...

Thanks for all the details. Followed them all and got my set working perfectly.