Bronco script emblem installed

[Escape2Bronco]

Any thoughts on which looks better?
One said it was oem but didn't come in that packaging. It's metal and said 3m on the back , but is flat dull.
The other is China, unknown adhesive, plastic, and shiny .

The 3M is just the adhesive material on the back.

Sponsored

 

[Escape2Bronco]

I wasn't clear. One has adhesive on the back that is labeled 3m. The other one's adhesive is unlabeled and blue covered. So known (unless they're lying) and unknown

So I'm trying to decide if i want the possibly fake oem that is dull or the I know it's cheap and a fake that is shiny.

Ok, gotcha. See if you can find another OEM one online to check out the packaging/adhesive protection color.

 

[Bamsi]

Any idea on how to remove dealer sticker without damaging paint? Would like to trade it for a bucking bronco...

 

[Mark S.]

Any idea on how to remove dealer sticker without damaging paint? Would like to trade it for a bucking bronco...

Use a heat gun to soften up the adhesive, then work around the edges carefully with a plastic spatula.

 

[Bamsi]

Use a heat gun to soften up the adhesive, then work around the edges carefully with a plastic spatula.

Thanks

 

[BodieBronco]

Please send pictures when done ,thank you .

Installed!! New bumper guard, bucking bronco, and script.
The blue tape worked wonderfully.
Of course, after I finished and walked away from a further distance, I worried the driver's side is at an angle.
What do you guys think? Does the script and the horse look good enough?

 

[Jrl]

Installed!! New bumper guard, bucking bronco, and script.
The blue tape worked wonderfully.
Of course, after I finished and walked away from a further distance, I worried the driver's side is at an angle.
What do you guys think? Does the script and the horse look good enough?

Perfect looks amazing. Black on that blue looks correct.

 

[Cactusjk]

Installed!! New bumper guard, bucking bronco, and script.
The blue tape worked wonderfully.
Of course, after I finished and walked away from a further distance, I worried the driver's side is at an angle.
What do you guys think? Does the script and the horse look good enough?

Looks great! How did you position and align the script emblem?

 

[BodieBronco]

Looks great! How did you position and align the script emblem?

Look. Back at pg one JLR's post with pictures of his white bronco. He told me "Take a look , this might help .Buy 1 inch blue tape and match it to the hood joint and then 1 inch from the vent . That’s what I did if you like that look . Good luck ."
I followed his advice. I did one inch blue painter's tape next to the vent vertically, one inch blue painter's tape by the hood joint/ edge. Then i find the wider blue painter's tape was the same width as the script. So i put that down next, then another strip of painter's tape below that. Removed the wider space holding tape, and cleaned the area really well and with alcohol wipe. Then i doubled checked that the script fit in the space..removed the 3m adhesive covering, and applied.

 

[Cactusjk]

Look. Back at pg one JLR's post with pictures of his white bronco. He told me "Take a look , this might help .Buy 1 inch blue tape and match it to the hood joint and then 1 inch from the vent . That’s what I did if you like that look . Good luck ."
I followed his advice. I did one inch blue painter's tape next to the vent vertically, one inch blue painter's tape by the hood joint/ edge. Then i find the wider blue painter's tape was the same width as the script. So i put that down next, then another strip of painter's tape below that. Removed the wider space holding tape, and cleaned the area really well and with alcohol wipe. Then i doubled checked that the script fit in the space..removed the 3m adhesive covering, and applied.

Thanks! Best to see the tape during install but I can work with that!

 

[Jrl]

Look. Back at pg one JLR's post with pictures of his white bronco. He told me "Take a look , this might help .Buy 1 inch blue tape and match it to the hood joint and then 1 inch from the vent . That’s what I did if you like that look . Good luck ."
I followed his advice. I did one inch blue painter's tape next to the vent vertically, one inch blue painter's tape by the hood joint/ edge. Then i find the wider blue painter's tape was the same width as the script. So i put that down next, then another strip of painter's tape below that. Removed the wider space holding tape, and cleaned the area really well and with alcohol wipe. Then i doubled checked that the script fit in the space..removed the 3m adhesive covering, and applied.

Actually jrl bronco is cactus gray first edition. Yes sometimes it looks white .

 

[BodieBronco]

Thanks! Best to see the tape during install but I can work with that!

Sorry I didn't think of taking pictures during the process. You got this though. It wasn't difficult. I just took my time and double checked. When i put the bronco on the back, i taped it on with blue tape just so i could step back and look at the placement in relation to everything else

 

[BodieBronco]

Actually jrl bronco is cactus gray first edition. Yes sometimes it looks white .

Oops, thanks for correcting me. It's really sharp looking

 

[Tomp611]

Did you all opt for matte or polished script emblems?

 

[Jrl]

Did you all opt for matte or polished script emblems?

Polished black on my First Edition.

Sponsored