Search results

In case you haven't guessed... I'm a Quality Engineer :inspect:

When trying to secure the Timberline towers to the Jetstream bars per the OEM instructions... After tightening with the Torque Screwdriver they give you... My towers did not grip, and could be easily slid back-and-forth by hand. I ended up back at Rack Attack Chicago where I bought them. The...

I have a narrow driveway, and I kept bumping my door into the neighbor's chain link fence... Found some Gray Door Edge Protectors on Amazon. I think they go well with the Cactus Gray... Installed in about 15 minutes.

Inspired by this post... I got a set of FL3Z17A954C Tow Hooks (for an F150) and bolted them up under the Bumper, There's an M8 1.25 pitch screw under there on a metal bracket... The hardware I used to replace the screw is in the pic. Yes... There's only one screw holding them on; No... I ain't...

The Yakima Jetstream bars with the Timberline Tower setup are 60" long; Yakima only sells 50", 60" and 70" in these bars. Yakima recommends the 60" bars for the BS; For what I carry, these were too long so I went with the 50". Note: Rack Attack (a Yakima Dealer) would not install the 50" bars...

Makes it easier if you ever run out of gas and have to fill from a jerry can. Helps with additives too.

I don't know the PN for the 2.0 Engine Cover... Try a search on https://www.oemfordpartscheap.com/ Ford says the Panel fits all BS Trims Funnel as shown. Hope this helps...

Maybe this will help... https://www.broncosportforum.com/forum/threads/installing-new-lettering-on-the-tailgate-of-bronco-sport-factory-lettering.6481/page-3#post-126573

I'm not sure... I think so. When you pickup your Bandlands... If it's not there, I'd ask about it.

For me, it's more of a "want" than a need. My understanding is, they are/were standard on the BS higher end trims. They were never standard on the Base or BB. https://carstopics.com/car-hood-bonnet-insulation/

Here's my posts and a few pics of the TufSkinz overlays: https://www.broncosportforum.com/forum/threads/installing-new-lettering-on-the-tailgate-of-bronco-sport-factory-lettering.6481/post-127007

Here's the Part Number for the Hood Insulator.... As of last week: Not in stock :frown: Insulator, Hood $94.84...

BS BB Wheel Upgrade for $9... https://www.amazon.com/dp/B07G8M9LLV?psc=1&ref=ppx_yo2ov_dt_b_product_details

Thanks Steve! I popped those rings off with a screwdriver and now all is well! You're the King!

I ordered Part Number M1PZ7860032AB; According Ford parts, these are supposed to fit a 2022 BS BB. They are cut perfectly, and line up OK; But, the snaps on the mat are different than the ones on my seat back... they won't snap together. Does anyone know of an alternative part number for these...

Here's my setup...

Just put on the matching fronts... I like.

I forgot to mention how much I love the look on a person's face when I tell them the engine only has three cylinders :shock:

I tell those Bronco, Jeep, and Tundra owner types that after the SHTF and folks are fighting over food, water and other essentials... I'll be 400 miles down the road while you guys are killing each other over the next tank of gas. And, those days are coming!

A lot of folks on this forum have been writing about stuff that's missing on their new BS. Here's my 2 cents; or 14,200 cents to be more precise. The way I understand it... There were shortages of many auto parts in 2021. Among these were the parts listed in the table below. Ford deemed these...