Search results

  1. Anyone have any idea why?

    For rear sensors sadly I know the Badlands never had them as standard - I have early Dec build. So not chip related. May have been model specific or part of the 360+ optional package. Ford was never clear on this or I would have ordered 360+. I think the blind spot system is what is used for...
  2. EVAP Leak

    Not the fuel tank (fortunately !). There is a plastic tank that is part of the EVAP system for collecting gasoline vapors that get recycled into engine. I would guess someone will make a metal after market part to replace the fabric/composite cover the car comes with so there is at least a...
  3. EVAP Leak

    I have early Dec badlands sport and it has a metal plate (thinner than forward plate), but it stops just short of where this canister seems to be. At that point the fabric cover (same material as wheel wells) starts and continues to rear along drivers side. Really a shame that fabric section...
  4. Undercarriage panel missing on right side of Badlands

    ce Someone looks like they have "disclosed" what is under the drivers side fiber cover - by "accident". This recent post looks like the drivers side area with the fiber cover. Sadly the metal plate just forward would have likely prevented their cracked EVAP tank resulting from running over...
  5. Texas Installed Side molding question

    There is a small triangular sticker with the model name on the front doors. These are not the same height even from side to side of the car so the side bumper piece can interfere with them if they were placed too low. Lots of mention on site about these. One reason some people may want dealer...
  6. Texas Installed Side molding question

    I found the template pretty useless that comes with side pieces. What I posted above is how I lined things up - use blue tape to hold it in place. Trick is to start at the door edge near handle on front door and not use template at front. As others have found the model stickers are never at...
  7. Blinding glare off windshield

    Possibly. If you look at them you'll see they taper and have side slopes so not a nice straight surface although you could certainly put something down the center part. Above my pay grade so I opted to just solve glare.
  8. Blinding glare off windshield

    I posted a description a couple months ago and here's a picture since you asked. Simple matte black film. Made a paper template to get shape on section angled towards windshield. Eliminates glare when driving into sun. I am sure this could be done fancier extending down the hood, but it will...
  9. Undercarriage panel missing on right side of Badlands

    I have early production BL. Looks exactly the same. Passenger side is metal, drivers side has the fiber cover. To me the fiber covers (like for wheel wells) are pretty worthless and just likely to trap dirt, but Ford must have felt they needed a cover on the drivers side. I am sure someone...
  10. Texas Installed Side molding question

    s Almost flush with door edge if you are looking at installing the Ford side molding. I found template hard to use, use so I used the door end to start alignment, then taped it to car and set forward end measuring up from bottom of door at both ends. Finally marked top edge position with tape...
  11. Hood Shocks installed

    And if you pull down slightly it holds the inner nut centered as you tighten. Easy to readjust so spacing on each side is equal once you see what it is doing, but good to remind people to check. I didn't have a deep socket so used box wrench which I think makes it easier to see what the nut is...
  12. Aftermarket leather steering wheel cover?

    I used this one. Amazon also has some custom cut ones listed which may fit a bit better at sides but at the time none specific for Sport. The side and bottom cover plates where wheel attaches are just loose enough to tuck in leather. This is stitch on. Easy to install. Looks depend on how...
  13. Buck N Penny present... Joshua Tree

    Curious if alarm goes off if you leave Penny in car alone and car is locked. Planning on relocation trip with cat and have seen issues with F150 alarms and dogs in car.
  14. 3D printed anything? Planning on it?

    Great idea. That opening leads directly a major electric connection that has been discussed as a failure point due to water exposure. Looking forward to seeing these installed.
  15. Took 20 years in development - the U260 prototype bronco

    The U260 was a proto-Bronco that deserved to live | Hagerty Media
  16. Dealer A-Plan higher than the A-Plan Table

    Note the a-plan calculator requires your zip code - plan varies on where dealer is located.
  17. has anyone had dealer add OEM backup sensor system?

    I have badlands without BL add on. Definitely no back up sensors, only rear cross traffic. Early Dec production. If you a way to turn it on I be interested.
  18. has anyone had dealer add OEM backup sensor system?

    Rear cross traffic alert does give you a sound alert. You can set the sensitivity level. Some say it is too sensitive, but for example backing up at our mail box station car pulled in as I was backing up about 20' away and sound alert went off. It is really confusing (and confounding) why...
  19. has anyone had dealer add OEM backup sensor system?

    This is an unpleasant surprise. While there is rear cross traffic alert if a car or person is moving behind you when backing up there is no traditional backup sensor that tells you if stationary object is behind you. Having placed an advance order last Sept I can tell you it wasn't clear...
  20. Questions/Concerns about Adhesive-based Modifications

    Long discussion here. Hood bulge glare | 2021+ Ford Bronco Sport Forum - Broncosportforum.com My solution was simple one to put 6x7 piece of matte black on bumps that reflect light. Works great. Could be integrated with other graphics if you want something fancier.


Advertisement
Top